Belt Plating Explained: Brass, Zinc and Gold
Share
Almost every message we get about plates is about the millimetres. 2mm, 4mm or 6mm. Hardly anyone asks the other two questions, and they matter just as much: what metal is under the gold, and what the gold actually is.
So here is the plain version. What gold plating is, what sits between the gold and the base metal, how brass and zinc differ, and why plating is not the same thing as paint.
What gold plated actually means
Gold plating is electroplating. The plate goes into a bath of salts carrying gold ions and is wired up as the negative electrode. Current runs through, the gold ions pick up electrons at the surface of the plate, and they come out of solution as solid metal bonded to the part. The anode is either gold, which dissolves to keep the bath topped up, or an inert material, in which case the bath has to be replenished as the gold is drawn out of it.
The number that matters is how much gold ends up there, and it is small. In jewellery terms, a gold layer under 0.5 microns is a gold flash or a gold wash. At 0.5 microns or more it is gold plated. At 2.5 microns or more it is heavy gold plated, which is the same threshold as vermeil. A micron is a thousandth of a millimetre, so even a heavy plate is about a four-hundredth of a millimetre of gold.
That is not a criticism of plating. It is how every plated object you own works, from a door handle to the connectors in your phone, and it has been industrial since the Elkington brothers took the first electroplating patents in 1840. It just means a gold plated belt is a belt with a gold surface. The character of the thing, the weight and the sharpness of the detail, comes from the metal underneath.
The layer nobody sees
Gold does not usually go straight onto the base metal. There is normally a nickel layer in between, and it does three jobs. It gives the soft gold a hard surface to sit on, it improves wear resistance, and it reduces the effect of the tiny pores that a thin gold layer always has.
It also stops a slow problem. On a copper-bearing base, copper atoms migrate up through the gold over time and tarnish it from underneath. Nickel blocks that. On zinc alloys there is one extra step, because nickel does not adhere well to zinc, so a thin copper strike goes down first. A strike is a deliberately thin first deposit, usually under 0.1 microns, laid down to give everything above it something to hold on to.
So the gold face of a belt plate is often four layers deep: base metal, copper strike, nickel, gold.
Brass or zinc under the gold
This is the question that changes how a belt feels in the hand.
Brass is a copper and zinc alloy, usually weighted at least two to one towards copper. Common brass runs about 63 per cent copper to 37 per cent zinc. It sits at 8.4 to 8.73 grams per cubic centimetre and melts between 900 and 940 degrees Celsius. It is harder than cast zinc, holds a crisp edge and takes a polish well, which is why a hand-finished brass plate like the one on our ROH Pure replica keeps its lettering sharp.
Zinc plates are not raw zinc. They are a zinc alloy, almost always from the Zamak family that the New Jersey Zinc Company developed in 1929. The name is an acronym of the German words for zinc, aluminium, magnesium and copper. Zamak 3, the reference alloy, is roughly 96 per cent zinc and 4 per cent aluminium and accounts for more than 70 per cent of all zinc die castings made in North America. It comes in at 6.4 grams per cubic centimetre and starts to melt at 380 degrees.
Two things follow from those numbers. The first is weight: the same plate in brass comes out around a third heavier than the same plate in zinc alloy, so a 4mm brass belt and a 4mm zinc belt do not weigh the same. The second is casting. Zinc alloy melts at less than half the temperature of brass, which is why finely detailed cast parts are usually zinc, and zinc takes electroplating, paint and chromate coatings well.
| Base metal | What it is | Density | Starts melting | What you notice |
|---|---|---|---|---|
| Brass | Copper and zinc, commonly about 63:37 | 8.4 to 8.73 g/cm³ | 900 to 940 °C | Heavier, harder, crisp edges, polishes bright |
| Zinc alloy (Zamak 3) | About 96% zinc, 4% aluminium | 6.4 g/cm³ | 380 °C | Lighter, casts very fine detail, plates easily |
Neither one is a cheat. What matters is that the maker tells you which you are getting. Our dual plated NWA Pacific Northwest replica and the NWA United States Heavyweight replica both name the metal and the thickness options on the page, which is how it should work.
How the shape gets made
Spin casting
Most small decorative metal parts are spin cast, and belt buckles, pins, emblems, medallions and trophies are the textbook examples. A rubber mould spins on its axis while molten metal is poured into the centre, and the spin pushes the metal out into the detail. Moulds are vulcanised silicone or organic rubber and last anywhere from a few hundred to over a thousand pulls.
It is a low temperature process, which is both the point and the limit. Overheat it and the rubber degrades. Tooling runs roughly 7,500 to 20,000 dollars against 50,000 to 2.5 million for die casting, and the first casting comes out in hours rather than the twelve to twenty-four weeks a die takes. Alloy choice matters too. Zamak 3 sets too quickly in a rubber mould and leaves a rough, porous surface the trade calls orange peel, so spin casters use Zamak 2, better known as Kirksite.
Die casting
Die casting holds tighter tolerances and the lowest price per piece, but the tooling bill and the lead time only pay off across very large runs. For a catalogue of hundreds of title designs, most ordered in ones and twos, the rubber mould is the route that works.
Either way, the mould decides the artwork, the plating decides the colour, and the thickness decides the weight. Keep those three separate and nothing on a belt page is confusing any more.
Plating is not paint
Plated metal is metal. It is deposited atom by atom and bonded to the surface underneath. A painted or lacquered finish is a film sitting on top of the metal, and the two age differently.
Painted zinc is a real product, not a myth. Zamak takes wet paint and chromate conversion coating as readily as it takes electroplating, so it is a legitimate and much cheaper way to finish a casting. It simply is not plating and should not be sold as plating.
You can usually tell them apart by how they fail. Plating wears thin at the high points first, where fingers and shoulders touch, and what shows through is the colour of the metal below. A film finish lifts and flakes, and it does it at edges and corners.
Antiquing is a different thing again, and it is deliberate. A darker tone is worked into the recesses so the raised artwork reads from across a room instead of flattening out under a bright polish. The ECW World Television replica and the NXT North American replica are both finished that way, and it is most of what makes a plate photograph like a television belt rather than a trophy.
Thickness changes the weight, not the finish
Worth saying plainly, because people assume the tiers are a quality ladder. They are not. A 6mm plate is not better plated than a 2mm plate off the same mould. It is the same artwork and the same plating, with three times the metal and a deeper side wall that casts a shadow against the leather.
Pick the tier by what you will do with the belt. Light for a wall, heavy for something that gets worn and handed around. The long version of that is in 2mm, 4mm or 6mm: which belt thickness to buy, and almost every belt in the full belt collection shows its tiers on the product page.
Looking after a plated belt
Two facts make the difference here.
Brass corrodes in the presence of moisture, chlorides, acetates, ammonia and certain acids, and it is particularly vulnerable to stress corrosion cracking from ammonia. Sweat carries chlorides and most household glass cleaners carry ammonia. So the two worst things you can do to a belt are put it away damp after wearing it, or clean it with the blue spray from under the sink.
The second is that a thin gold layer has pores. The nickel underneath limits what gets through, but handling is still what wears a plated surface, and always at the high points first.
Which gives you the whole routine: a dry soft cloth, nothing abrasive, no dipping solutions, a wipe down after the belt is worn, and no damp garages or lofts.
Four questions before you buy
Whoever you buy from, ask these. What is the plate metal. What thickness. Is the finish plated or coated. Is the strap real leather. Any maker who can answer all four in a sentence each is worth buying from.
For sizing, how to measure a championship belt covers it. For something that does not exist yet, how to design a custom championship belt walks through the artwork side. And for the designs themselves, every WWE belt design explained and the NWA territory era are where to start.
How we build them
Every Elitestraps belt is a replica, made to order by hand in our own workshop. Plates are cast, finished and plated in house in 2mm, 4mm and 6mm, with 8mm and 10mm on selected designs, and the leather is cut and stitched to the plates before a final check. Production runs nine business days and delivery is free worldwide with duties included, so nothing is collected at your door. The whole range is in the all belts collection, and buyer reviews are on Trustpilot.
All Elitestraps belts are replicas made by us. They are not official or licensed products. Elitestraps is not affiliated with or endorsed by WWE, AEW, UFC, NJPW, NWA, TNA, ECW or any other wrestling or sports promotion, and all names and titles mentioned above are referred to for historical description only.